A sprinkler system can look perfectly normal from the sidewalk while wasting water below ground, soaking a foundation edge, or leaving expensive landscaping dry. This sprinkler system inspection guide helps Texas homebuyers, sellers, and homeowners understand what should be checked, what common problems mean, and when a closer professional evaluation is warranted.
In Central and South Texas, irrigation systems work hard. Long hot stretches, shifting soils, hard water, active landscaping, and periodic freezes all put pressure on components that are mostly hidden from view. A quick walk-around is useful, but it does not always reveal how the system performs zone by zone or whether water is reaching the areas it is meant to protect.
Why a Sprinkler Inspection Matters in Texas
A sprinkler system is more than a convenience. It affects water bills, plant health, drainage patterns, fencing, sidewalks, and sometimes the home itself. Overspray can stain masonry, water a neighbor’s property, or encourage moisture near the foundation. A leak at a valve box may go unnoticed for months, especially if the system runs while everyone is asleep or away.
For a buyer, irrigation concerns can change the true cost of a property after closing. Replacing a few sprinkler heads is relatively minor. Repairing damaged wiring, multiple valves, a controller, broken lateral lines, or a backflow assembly can be more involved. For a seller, identifying obvious deficiencies before listing can prevent a small system issue from becoming a late-stage negotiation point.
Texas soil conditions add another layer. Expansive clay soils around Austin, San Marcos, Kyle, Buda, and San Antonio can move as moisture levels change. No irrigation system can eliminate foundation movement, and watering practices should never be treated as a universal foundation solution. Still, uncontrolled runoff, broken heads, and persistent saturation near the structure deserve attention.
What a Sprinkler System Inspection Should Cover
A meaningful inspection starts with operation, not just a visual look at the controller. The inspector should run accessible zones and observe the system while it is operating. Some systems have locked controls, damaged controllers, disconnected power, seasonal shutdowns, or unknown programming. Those conditions may limit what can be tested, and the inspection report should clearly state the limitation.
Controller and zone operation
The controller should power on, respond to manual commands, and activate each available zone. Inspectors look for zones that fail to start, run continuously, activate at the wrong time, or operate alongside another zone unexpectedly. These symptoms may point to controller programming, wiring, solenoid, or valve concerns.
The schedule matters, but it should be viewed in context. A setting that is reasonable in July may be excessive during cooler or wetter periods. Systems with rain or soil-moisture sensors may help reduce unnecessary watering, but those devices must be installed, connected, and functioning properly to provide any benefit.
Sprinkler heads and coverage
While each zone runs, the inspection should identify broken, missing, tilted, clogged, sunken, or improperly adjusted heads. Pop-up heads that do not rise fully can water the surrounding grass instead of the intended area. Heads that spray sidewalks, streets, windows, siding, fences, or exterior doors waste water and can contribute to staining or deterioration over time.
Coverage is equally important. Dry spots may mean a head is blocked by vegetation, set too low, damaged, or simply poorly placed. Conversely, a heavy stream striking one portion of the yard can create runoff. Plants grow, landscaping changes, and prior repairs are not always coordinated with the original design. Even a system that once worked well may need adjustment.
Valves, valve boxes, and visible leaks
Valve boxes should be reasonably accessible and free of standing water when conditions are dry. Water inside a box does not automatically prove a leak, especially after rain or irrigation, but it is worth evaluating. A valve that does not close fully may allow a zone to seep or run after the controller has shut it off.
Inspectors also watch for unusually wet turf, soft soil, pooling, erosion, or water surfacing between sprinkler heads. These conditions can indicate a damaged underground line, although the exact location and repair scope generally require irrigation troubleshooting beyond a standard visual inspection.
Backflow protection
Backflow prevention helps keep irrigation water from reversing direction into the potable water supply. The visible assembly should be checked for damage, leaks, missing insulation, and improper conditions around the device. In many Texas jurisdictions, backflow assemblies require periodic testing by a qualified and licensed backflow prevention assembly tester. A general inspection can identify visible concerns, but it is not a substitute for the required performance test.
Freeze damage is a recurring issue after severe winter weather. Cracked brass fittings, split piping, dripping shutoff valves, and damaged insulation may not be obvious until the system is turned back on. If a home has been vacant or the irrigation system was winterized, ask whether it has been recommissioned and tested.
Issues Homeowners Commonly Miss
Not every irrigation problem creates a dramatic geyser. Slow leaks and poor adjustments often cause the most frustration because they develop quietly.
A consistently green patch in an otherwise dry yard can signal a leaking line or valve. A spike in the water bill without a clear household explanation can point to irrigation use or a leak. Water running down a driveway after a zone starts may indicate poor drainage, excessive run time, or a broken component. These clues do not identify the exact repair, but they give a homeowner a reason to investigate.
Another common issue is mismatched precipitation. Spray heads, rotary nozzles, and drip irrigation deliver water at different rates. When they are combined on the same zone, one landscape area may be overwatered while another receives too little. A properly functioning system is not necessarily an efficiently designed system.
Tree roots, lawn equipment, settling soil, and construction activity can also affect buried lines and wiring. A recent fence replacement, patio installation, pool project, or landscaping renovation is a good reason to operate every zone afterward. Irrigation damage is easy to cause and easy to overlook until the next watering cycle.
A Practical Homeowner Check Between Inspections
Homeowners do not need to diagnose every irrigation component, but a brief seasonal check can catch obvious changes. Run one zone at a time during daylight and walk the property. Watch the heads rise, look for overspray and dry areas, and listen for water running where it should not.
Pay particular attention to the foundation perimeter, exterior walls, gates, driveways, and street-side areas. Water should be directed to landscaping, not against the home or into places where it creates a slip hazard or nuisance. Trim vegetation that blocks heads, but avoid digging near valve boxes or lines unless you know where utilities and irrigation components are located.
If the controller has been reset after a power outage, confirm the date, time, and program. A wrong clock setting can cause watering at inconvenient times, while a default schedule may run longer or more often than intended. During restrictions or drought conditions, always follow local water rules rather than relying on an old controller program.
When to Call a Specialist
A professional irrigation contractor is the right next step when zones do not operate, valves leak, wiring faults are suspected, water pressure is inconsistent, or underground leaks may be present. Backflow testing should be handled by an appropriately qualified tester where required. If an inspection identifies a concern, prompt evaluation is usually less costly than waiting for landscape damage, water loss, or a larger failure.
For buyers, ask for records of recent repairs, backflow testing, warranties, and controller instructions when they are available. For sellers, having the system operating and accessible during the inspection helps create a clearer picture of its condition. Texas Inspections Today includes clear observations and limitations in reporting so clients can make decisions with the right level of confidence.
A well-adjusted sprinkler system should fade into the background: watering the landscape where it belongs, protecting neither the lawn nor the home at the expense of the other. If something looks off during a routine walk-through, treat that small sign as useful information and address it before the next season makes it larger.